Thrift Store Find: iZone Digital Combo

I see lot's of Polaroid iZone cameras at the thrift stores, but this is the first time I've run across this particular model. I've never heard of it before either. It's called the iZone Digital Combo camera. It's an iZone camera with a built-in digital camera added to the top. According to the Land List, it was produced in 2000-2001 and originally cost $99.95.

It sports a .3Mp digital camera with 1Mb of memory, 18 digital photos at 680x480p, an RS-232 serial PC connection, an optical viewfinder with no display LCD.

The iZone section of the camera is a standard iZone camera. The analog and digital cameras are separate from each other, but appear to share the same power source, since there is a switch to transfer the 4-AAA power source from one camera to the other.

Unlike most of my thrift store purchases, I don't consider this a usable camera, as iZone film is no longer available and the digital camera requires an outdated PC connection and PC software to download the photos.

Cost: $5.99

Polaroid Land Camera - Battery Conversion Mod

This is one of the most requested videos I have on my to do list. I'm still working on the video, but here is the Words and Pictures version of it.

The metal body folding Polaroid Land cameras use an odd battery that has snaps on either end.

These Polaroid cameras use either a 3v #532 battery, or a 4.5 volt #531 battery.

To identify which battery your camera uses, open the battery compartment and read the engraved type on the back of the compartment door.

If you are shopping for a Polaroid Pack camera, I would recommend looking for a 3 volt camera, as it is easier to convert.

The chart below identifies which Polaroid Pack camera models use what type of battery:

3 volt cameras, #532 battery

103, 104, 125, 135, 210, 215, 315, 320, 330, 420, 430, 440, M60, and Countdown 70

The following cameras use two 3 volt, #532 batteries, one of which is used for the built-in electronic development timer. 

If converting one of these cameras, you need only replace the camera shutter battery.

335, 350, 360, 450, M80, and Countdown 90

4.5 volt cameras, #531 battery:

100, 101, 102, 220, 225, 230, 240, 250, and 340

3-Volt Mods

3 Volt Mod - Version 1:

This is the quick and dirty mod for 3v cameras can be done using a 3v lithium battery.

Tools and Parts needed:

• Utility knife
• Electrician's Tape
• CR 123 3v battery (or equivalent)

Step 1:

The unwind the wires that are looped around the plastic end of the snaps.

Step 2:

Cut the wires close to the snap.

Step 3:

Strip about 1/4" (3-4mm) of insulation from the ends of the wires.

Step 4:

Tape the white wire to the positive end of the battery.

Step 5:

Tape the black wire to the negative end of the battery.

Step 6:

Insert the taped battery in the battery clip.

Check the shutter to make sure you have a positive connection to the battery.

3 Volt Mod - Version 2:

This is the more elegant version of the 3 volt mod. It uses a 2 AAA cell battery holder. I got mine from Radioshack, but any equivalent will do. The uncovered version is better, as the enclosed battery pack is slightly too large for the battery compartment.

Tools and Parts needed:

• Utility knife
• Electrician's Tape
• 2-cell AAA battery holder (Radioshack part #270-398B or equivalent)
• phillips screwdriver (if you need to remove a screw-mounted battery holder)
• needle nose pliers (if you need to remove a built in battery holder)

Follow Steps 1-3 above.

Step 4b:

Take the black wire of the battery pack, and match it up with the black wire of the camera.

Step 5b:

Twist the wires together. Wrap the two wires together with a  1.5" length of electrical tape.

Repeat these steps with the red and white wires.

Optional: If you are handy with a soldering iron, solder the wires together for the best connection.

Step 6b:

Step 7b:

You need to make room for the battery holder. If the battery clip screwed in, remove it with a small phillips screwdriver. If the battery clip is molded into the same plastic as the camera, you will have to remove it by nibbling at it with a pair of small needle nose pliers. 

Note: A photograph will be added later, after I shoot the clip removal for the how-to video.

4.5 Volt Mod - Version 1:

This is the same as the 3 volt mod, version 2, except at the end. The 3 cell battery holder won't fit inside the battery compartment, se we need to make a notch in the battery compartment for the wires to come out. 

Tools and Parts needed:

• Utility knife
• Electrician's Tape
• 3-cell AAA battery holder (Radioshack part #270-42 or equivalent)
• glue or velcro to attach the battery holder to the camera

Follow Steps 1-3 from the 3 volt, Version 1

Follow Steps 4b-6b from the 3 volt, Version 2, except you are connecting a 3 cell, 4.5 volt battery holder instead of the 2 cell holder.

Step 7c:

With the utility knife, start to scrape a notch to the left of the bump in the battery compartment door edge. You don't want to put the notch in the bump, as the bump is what holds the battery compartment door closed.

The battery compartment is metal, but it's aluminum, so it can be cut by using the cutting edge of the utility knife to scrape a notch into the metal. Scrape the metal to remove it, by applying pressure, and dragging the blade perpindicular to the compartment edge (in the direction of the arrow). Once you get a slight divot going, it gets easier to cut down into the metal. Little shavings will come off as you cut into the metal.

Step 8c:

The finished notch.

Step 9c:

The battery pack can be attached to the camera with glue or industrial velcro applied to the battery pack and to the camera body.

To come: 4.5 volt mod, Version 2.

There is a more elegant solution for the 4.5 volt mod, but it involves modifying a 4-cell holder so that it holds 3 batteries. This is a lot of work, but the advantage is that the battery holder will fit inside the battery compartment.

I will post this 4-cell battery holder to 3-cell battery holder later, as I need to improve my light set-up, so that you can see what is being done to modify the battery holder. 

FYI:

For those of you who are not technically inclined, you can still find batteries (#531 4.5v, #532 3v) at Amazon.com.

Polaroid Folding Land Camera Batteries:

Exell A19PX/ 531 4.5v battery

http://www.amazon.com/Exell-A19PX-V19PX-Alkaline-Battery/dp/B000ANETWC/ref=sr_1_1?s=electronics&ie=UTF8&qid=1344469962&sr=1-1&keywords=battery+531+4.5v

Exell A24PX/ 532 3v battery

http://www.amazon.com/Exell-A24PX-V24PX-Alkaline-Battery/dp/B005MCCA9K/ref=sr_1_1?s=electronics&ie=UTF8&qid=1344470095&sr=1-1&keywords=battery+532+3v

The Lomography Diana Instant Back

This is an adapter to use Fujifilm's Instax Mini film with the Lomography Diana +, F+ and Diana F+ clone cameras. It won't work with vintage Diana cameras or Holga.

The prints are 8.6cm x 5.4th with an image size of 6.2cm x 4.6 cm.

Out of the Box , Installation and Loading videos are on the way.

Polaroid announcements

A little off-topic for this blog, but newsworthy.

For those of you who shoot Polaroid, some interesting news.

First of all, there's a group on the web that claims to have purchased
some of the integral film production equipment from Polaroid. They
hope to bring back integral film (600 and maybe even Spectra?).

http://www.the-impossible-project.com/beta/

The other bit of news is that Polaroid is going to be launching a new
digital camera with a built in printer. Not quite like an old integral
polaroid, but the possibilities are interesting.

It's a 5mp camera with an LCD screen so that photos can be previewed
before printing. It's a thermal printer, so no ink cartridges will be
necessary, and the paper packs will be significantly cheaper than the
old integral films.

Polaroid Press Release